PVA glue does not hurt the foam, use it
| The One Ring http://test.one-ring.co.uk/ |
|
| High density blue polystyrene http://test.one-ring.co.uk/viewtopic.php?f=7&t=21227 |
Page 1 of 1 |
| Author: | IM A ENT!!! [ Mon Jul 18, 2011 2:00 pm ] |
| Post subject: | High density blue polystyrene |
I making a diorama and using some blue foam as its base(25 mm). I want to put it on a wooden decorative base like a plaque or plark. Can the blue foam be PVA glued to the wooden base or would i need some plastic card underneath the foam first and then PVA the plastic card to the wooden base. Basicly i want to know what will make the diorama more structualy sound and strong. So plastic card needed ? or just the blue foam over the wooden base ? thankyou |
|
| Author: | Bastion.HUN [ Mon Jul 18, 2011 8:24 pm ] |
| Post subject: | Re: High density blue polysterne |
PVA glue does not hurt the foam, use it
|
|
| Author: | ForgottenLore [ Mon Jul 18, 2011 10:15 pm ] |
| Post subject: | Re: High density blue polysterne |
It may cause some warping as it dries though, best to weight the whole thing down real well until the glue is thoroughly dry. |
|
| Author: | Dagorlad [ Thu Jul 21, 2011 8:16 am ] |
| Post subject: | Re: High density blue polysterne |
PVA needs air to dry, so it will take a while for it to set properly. But it works perfectly well and will form a strong bond eventually. |
|
| Author: | Oldman Willow [ Thu Jul 21, 2011 1:01 pm ] |
| Post subject: | Re: High density blue polysterne |
Quote: PVA needs air to dry, so it will take a while for it to set properly. But it works perfectly well and will form a strong bond eventually. You might want to look for a product called Liquid Nails for small projects. Contractors can't wait for white glue to dry so they use special nail guns or Liquid nails in caulk guns to hang insulation foam. |
|
| Author: | Hilbert [ Thu Jul 21, 2011 1:49 pm ] |
| Post subject: | Re: High density blue polysterne |
Of course, it will be perfect if you give it time to dry... |
|
| Author: | IM A ENT!!! [ Wed Jul 27, 2011 1:48 pm ] |
| Post subject: | Re: High density blue polysterne |
Ok, cool, thank you all very much. (gee this forum is super helpful  )
|
|
| Author: | Slythar [ Thu Jul 28, 2011 2:30 am ] |
| Post subject: | Re: High density blue polysterne |
Quote: You might want to look for a product called Liquid Nails for small projects. Contractors can't wait for white glue to dry so they use special nail guns or Liquid nails in caulk guns to hang insulation foam. There is also a product called 'No More Nails' by Lepage, same stuff. It's really hard to not get it glued down with this stuff but it costs much more than PVA glue. Good for first timer though and also perfect for sealing/strengthening the ends and edges. You can glue it straight to the wood. Just roughen up the wood and foam with sand paper then spread adhesive evenly on wood. Put on the foam and give it a twist when putting it on so its snug. Set weight evenly on top of foam and let it set for 24 hours with No More Nails or 2-3 days with glue. |
|
| Author: | Dagorlad [ Fri Jul 29, 2011 10:14 am ] |
| Post subject: | Re: High density blue polysterne |
I've had problems with Liquid Nails and styrofoam - it stops sticking after a while and comes apart. So I don't use it anymore and stick to PVA (sorry, bad pun). |
|
| Author: | Oldman Willow [ Fri Jul 29, 2011 12:33 pm ] |
| Post subject: | Re: High density blue polystyrene |
Quote: I've had problems with Liquid Nails and styrofoam - it stops sticking after a while and comes apart. So I don't use it anymore and stick to PVA (sorry, bad pun). That is interesting. I have had a different experience with Liquid Nails. I can't get the (expletive deleted) stuff off plywood.The Styrofoam is not strong enough to resist much force so it breaks off the glue. The glue however is very difficult to remove from salvaged plywood. At least you can sand PVA down if the Styrofoam breaks off the glue. If you properly clamp and press Styrofoam to plywood with PVA or Liquid Nails you will not get it off in one piece. I think the PVA ( a carpenters brand not school glue) would create a stronger bond if it is pressed and clamped because the PVA will find its way into the porous Styrofoam and grip better. The Styrofoam products sold for home insulation have a vapor barrier that might prevent PVA from bonding at all.Remove it and ruff up the surface before you glue and clamp. It will take a week to cure. If it is a small piece It might be ok after a few days. |
|
| Page 1 of 1 | All times are UTC |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|