|
It is currently Thu Nov 28, 2024 8:46 am
|
View unanswered posts | View active topics
|
Page 1 of 1
|
[ 4 posts ] |
|
Author |
Message |
elliodoc
|
Post subject: Planning my moria board - How wide a tunnel can be blocked?
Posted: Fri Oct 26, 2012 10:06 am
|
|
Joined: Mon Jul 09, 2012 1:32 pm Posts: 79
|
Hi all,
I have another noob question that will help me plan my moria board. I would be grateful for your help.
If I understand the basic rules correctly, a model can't move within 20mm of another (the control zone) unless it's gong to charge all the way into combat. Therefore I assume a typical mini with 25mm base can block a tunnel that's less than 115mm wide by standing in the middle of it. I assume if it stood in the middle then it blocks 25mm by its base, plus 20mm on either side by its control zone, leaving less than 25mm on either side for another mini to squeeze past? Is this right? 115mm seems quite wide.
For the sake of argument I'm assuming both models have 25mm bases.
Thank you.
|
|
Top |
|
|
SidTheSloth
|
Post subject: Re: Planning my moria board - How wide a tunnel can be block
Posted: Fri Oct 26, 2012 10:24 am
|
|
Joined: Sun Jun 10, 2012 8:52 pm Posts: 1815 Images: 10
|
yes, that is right bbuuuutt... if your defending model is in combat then the control zone has no effect. then the enemy could clip past and stab you in the back.
_________________ 'Though my memory's fading, I remember two things very clearly: I am a great sinner and Christ is a great Savior' -John Newton
|
|
Top |
|
|
elliodoc
|
Post subject: Re: Planning my moria board - How wide a tunnel can be block
Posted: Fri Oct 26, 2012 10:31 am
|
|
Joined: Mon Jul 09, 2012 1:32 pm Posts: 79
|
OK that makes sense. An attacker could throw a cheap warrior at a blocking hero with the sole intention of keeping them busy (ie negating the control zone) so that other stronger models can slip past.
Presumably a tunnel less than 75mm wide could block a passage until the blocking model was slain, as the control wouldn't then be needed to stop others slipping past. Base widths alone would be sufficient.
Ta.
|
|
Top |
|
|
Beowulf03809
|
Post subject: Re: Planning my moria board - How wide a tunnel can be block
Posted: Fri Oct 26, 2012 1:48 pm
|
|
Joined: Mon Aug 21, 2006 12:53 pm Posts: 1827 Location: CO, USA
|
That's about right if you are trying to set up a couple choke points in the game board. It will be up to the players to get to these points first and use them to the max.
As a warning…choke points of any sort can make a game long, tedious, boring or frustrating (or all the above!). So be cautious. This goes for rivers with bridge crossings, tunnels, etc. I’ve played both LotR and historical games where a bad table set up really robbed the fun for both sides simply due to a really successful choke point.
If it’s there for a specific scenario purpose (such as Gandalf holding the Bridge long enough for the others to escape) then that’s great. If it’s a general board for random play you should look at ways that the opponent can get around the choke point (even if it’s a longer route they have to fight their way through). Or if you are playing with goblins or spiders or such where they can climb as easy as walk then they may be able to get by via the walls (or at least get more attacks on the defender by leveraging the walls in addition to the floor). But against an army with really high Defense or similar advantages a good choke point can be as bad as facing a full-bows Grey Company army or similar one-sided games.
_________________ Wait ye the finish! The fight is not yours.Beowulfhttp://TacticsInMiniature.com
|
|
Top |
|
|
|
Page 1 of 1
|
[ 4 posts ] |
|
Who is online |
Users browsing this forum: No registered users and 118 guests |
|
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot post attachments in this forum
|